1. root@OpenWrt:~# dmesg
2. [    0.000000] Linux version 6.6.73 (builder@buildhost) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r28427-6df0e3d02a) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 Mon Feb  3 23:09:37 2025
3. [    0.000000] Board has DDR2
4. [    0.000000] Analog PMU set to hw control
5. [    0.000000] Digital PMU set to hw control
6. [    0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
7. [    0.000000] printk: bootconsole [early0] enabled
8. [    0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
9. [    0.000000] MIPS: machine is TP-Link Archer C5 v4
10. [    0.000000] Initrd not found or empty - disabling initrd
11. [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
12. [    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
13. [    0.000000] Zone ranges:
14. [    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
15. [    0.000000] Movable zone start for each node
16. [    0.000000] Early memory node ranges
17. [    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
18. [    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
19. [    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
20. [    0.000000] pcpu-alloc: [0] 0
21. [    0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
22. [    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
23. [    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear)
24. [    0.000000] Writing ErrCtl register=0003e4f3
25. [    0.000000] Readback ErrCtl register=0003e4f3
26. [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 16240
27. [    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
28. [    0.000000] Memory: 55152K/65536K available (6658K kernel code, 620K rwdata, 880K rodata, 1240K init, 241K bss, 10384K reserved, 0K cma-reserved)
29. [    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
30. [    0.000000] NR_IRQS: 256
31. [    0.000000] CPU Clock: 580MHz
32. [    0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
33. [    0.000000] systick: enable autosleep mode
34. [    0.000000] systick: running - mult: 214748, shift: 32
35. [    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
36. [    0.000002] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
37. [    0.007676] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
38. [    0.073580] pid_max: default: 32768 minimum: 301
39. [    0.090795] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
40. [    0.097853] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
41. [    0.116767] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=1.
42. [    0.133811] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
43. [    0.143396] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
44. [    0.153267] pinctrl core: initialized pinctrl subsystem
45. [    0.162395] NET: Registered PF_NETLINK/PF_ROUTE protocol family
46. [    0.168955] thermal_sys: Registered thermal governor 'step_wise'
47. [    0.173087] /pinctrl: Fixed dependency cycle(s) with /pinctrl/pinctrl0
48. [    0.460362] PCI host bridge to bus 0000:00
49. [    0.464302] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
50. [    0.471014] pci_bus 0000:00: root bus resource [io  0x10160000-0x1016ffff]
51. [    0.477647] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
52. [    0.485408] pci 0000:00:00.0: [1814:0801] type 01 class 0x060400
53. [    0.491198] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
54. [    0.497286] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff]
55. [    0.503497] pci 0000:00:00.0: supports D1
56. [    0.507339] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
57. [    0.514933] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
58. [    0.522976] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
59. [    0.528796] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
60. [    0.535436] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
61. [    0.541987] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
62. [    0.548252] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
63. [    0.554643] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
64. [    0.561122] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
65. [    0.567487] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
66. [    0.574265] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
67. [    0.580844] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
68. [    0.587869] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
69. [    0.594461] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
70. [    0.601577] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
71. [    0.608569] pci 0000:00:00.0: PCI bridge to [bus 01]
72. [    0.613397] pci 0000:00:00.0:   bridge window [mem 0x20000000-0x200fffff]
73. [    0.619978] pci 0000:00:00.0:   bridge window [mem 0x20100000-0x201fffff pref]
74. [    0.628696] clocksource: Switched to clocksource systick
75. [    0.647550] NET: Registered PF_INET protocol family
76. [    0.652604] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
77. [    0.661452] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear)
78. [    0.669704] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
79. [    0.677185] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
80. [    0.684638] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
81. [    0.691497] TCP: Hash tables configured (established 1024 bind 1024)
82. [    0.698511] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear)
83. [    0.705922] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
84. [    0.712268] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
85. [    0.720200] NET: Registered PF_UNIX/PF_LOCAL protocol family
86. [    0.725754] PCI: CLS 0 bytes, default 32
87. [    0.729824] rt-timer 10000100.timer: maximum frequency is 1220Hz
88. [    0.742913] workingset: timestamp_bits=14 max_order=14 bucket_order=0
89. [    0.751365] squashfs: version 4.0 (2009/01/31) Phillip Lougher
90. [    0.756983] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
91. [    0.773836] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
92. [    0.783419] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
93. [    0.796119] printk: console [ttyS0] disabled
94. [    0.800897] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
95. [    0.810613] printk: console [ttyS0] enabled
96. [    0.819068] printk: bootconsole [early0] disabled
97. [    0.867288] spi spi0.0: force spi mode3
98. [    0.872096] spi-nor spi0.0: s25fl064k (8192 Kbytes)
99. [    0.877211] 6 fixed-partitions partitions found on MTD device spi0.0
100. [    0.884190] Creating 6 MTD partitions on "spi0.0":
101. [    0.889157] 0x000000000000-0x000000020000 : "u-boot"
102. [    0.898291] 0x000000020000-0x0000007c0000 : "firmware"
103. [    0.906659] 2 tplink-fw partitions found on MTD device firmware
104. [    0.912805] Creating 2 MTD partitions on "firmware":
105. [    0.917878] 0x000000000000-0x000000277421 : "kernel"
106. [    0.922957] mtd: partition "kernel" doesn't end on an erase/write block -- force read-only
107. [    0.933880] 0x000000277424-0x0000007a0000 : "rootfs"
108. [    0.939051] mtd: partition "rootfs" doesn't start on an erase/write block boundary -- force read-only
109. [    0.950970] mtd: setting mtd3 (rootfs) as root device
110. [    0.956250] 1 squashfs-split partitions found on MTD device rootfs
111. [    0.962635] 0x000000650000-0x0000007a0000 : "rootfs_data"
112. [    0.970854] 0x0000007c0000-0x0000007d0000 : "config"
113. [    0.978513] 0x0000007d0000-0x0000007e0000 : "rom"
114. [    0.986544] 0x0000007e0000-0x0000007f0000 : "romfile"
115. [    0.994745] 0x0000007f0000-0x000000800000 : "radio"
116. [    1.038057] gsw: setting port4 to ephy mode
117. [    1.049178] mtk_soc_eth 10100000.ethernet: port 5 - using fixed link parameters
118. [    1.056900] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
119. [    1.063805] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
120. [    1.073244] rt2880_wdt 10000120.watchdog: Initialized
121. [    1.081109] NET: Registered PF_INET6 protocol family
122. [    1.094576] Segment Routing with IPv6
123. [    1.098443] In-situ OAM (IOAM) with IPv6
124. [    1.102747] NET: Registered PF_PACKET protocol family
125. [    1.107966] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
126. [    1.121584] 8021q: 802.1Q VLAN Support v1.8
127. [    1.171335] clk: Disabling unused clocks
128. [    1.186836] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
129. [    1.200933] Freeing unused kernel image (initmem) memory: 1240K
130. [    1.206988] This architecture does not have kernel memory protection.
131. [    1.213597] Run /sbin/init as init process
132. [    1.217773]   with arguments:
133. [    1.217780]     /sbin/init
134. [    1.217786]   with environment:
135. [    1.217793]     HOME=/
136. [    1.217799]     TERM=linux
137. [    2.188969] init: Console is alive
138. [    2.193140] init: - watchdog -
139. [    3.731312] kmodloader: loading kernel modules from /etc/modules-boot.d/*
140. [    3.829307] usbcore: registered new interface driver usbfs
141. [    3.835099] usbcore: registered new interface driver hub
142. [    3.840689] usbcore: registered new device driver usb
143. [    3.850674] gpio_button_hotplug: loading out-of-tree module taints kernel.
144. [    3.882445] phy phy-usbphy.0: remote usb device wakeup disabled
145. [    3.888528] phy phy-usbphy.0: UTMI 16bit 30MHz
146. [    3.893078] ehci-platform 101c0000.ehci: EHCI Host Controller
147. [    3.898974] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
148. [    3.907227] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
149. [    3.923295] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
150. [    3.931080] hub 1-0:1.0: USB hub found
151. [    3.936149] hub 1-0:1.0: 1 port detected
152. [    3.951545] rtl8367b rtl8367s: using MDIO bus 'mdio'
153. [    3.957392] rtl8367b rtl8367s: RTL8367S-VB chip found (num:6642 ver:0010)
154. [    4.309894] rtl8367b rtl8367s: alloc vlan mc emulator
155. [    4.324947] rtl8367b rtl8367s: cpu_port:7, assigned to extif1
156. [    4.759212] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
157. [    4.766285] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
158. [    4.774522] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
159. [    4.810367] hub 2-0:1.0: USB hub found
160. [    4.815413] hub 2-0:1.0: 1 port detected
161. [    4.833116] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
162. [    4.845299] init: - preinit -
163. [    8.848933] random: crng init done
164. [   10.539003] mtk_soc_eth 10100000.ethernet eth0: port 5 link up (1000Mbps/Full duplex)
165. [   10.547976] 8021q: adding VLAN 0 to HW filter on device eth0
166. [   12.336769] jffs2: notice: (487) jffs2_build_xattr_subsystem: complete building xattr subsystem, 138 of xdatum (14 unchecked, 124 orphan) and 142 of xref (124 dead, 0 orphan) found.
167. [   12.355794] mount_root: switching to jffs2 overlay
168. [   12.363796] overlayfs: upper fs does not support tmpfile.
169. [   12.394397] urandom-seed: Seeding with /etc/urandom.seed
170. [   12.508087] mtk_soc_eth 10100000.ethernet eth0: port 5 link down
171. [   12.542460] procd: - early -
172. [   12.545756] procd: - watchdog -
173. [   13.161681] procd: - watchdog -
174. [   13.166581] procd: - ubus -
175. [   13.325946] procd: - init -
176. [   15.384485] kmodloader: loading kernel modules from /etc/modules.d/*
177. [   16.169961] jitterentropy: Initialization failed with host not compliant with requirements: 9
178. [   16.655528] Loading modules backported from Linux version v6.12.6-0-ge9d65b48ce1a
179. [   16.663268] Backport generated by backports.git v6.1.110-1-35-g410656ef04d2
180. [   17.334344] mt76x2e 0000:01:00.0: card - bus=0x1, slot = 0x0 irq=4
181. [   17.341046] mt76x2e 0000:01:00.0: ASIC revision: 76120044
182. [   18.060480] mt76x2e 0000:01:00.0: ROM patch build: 20141115060606a
183. [   18.091170] mt76x2e 0000:01:00.0: Firmware Version: 0.0.00
184. [   18.096810] mt76x2e 0000:01:00.0: Build: 1
185. [   18.101055] mt76x2e 0000:01:00.0: Build Time: 201607111443____
186. [   18.166259] mt76x2e 0000:01:00.0: Firmware running!
187. [   18.189490] mt76x2e 0000:01:00.0: registering led 'mt76-phy0'
188. [   18.197494] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
189. [   18.473090] PPP generic driver version 2.4.2
190. [   18.500675] NET: Registered PF_PPPOX protocol family
191. [   18.652189] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
192. [   18.660731] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 7620 detected
193. [   18.669777] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
194. [   19.137843] jitterentropy: Initialization failed with host not compliant with requirements: 9
195. [   20.019722] kmodloader: 1 module could not be probed
196. [   20.025122] kmodloader: - jitterentropy_rng - 0
197. [   64.373745] mtk_soc_eth 10100000.ethernet eth0: port 5 link up (1000Mbps/Full duplex)
198. [   64.382699] 8021q: adding VLAN 0 to HW filter on device eth0
199. [   64.490953] br-lan: port 1(eth0.1) entered blocking state
200. [   64.496528] br-lan: port 1(eth0.1) entered disabled state
201. [   64.502177] eth0.1: entered allmulticast mode
202. [   64.506640] mtk_soc_eth 10100000.ethernet eth0: entered allmulticast mode
203. [   64.513977] eth0.1: entered promiscuous mode
204. [   64.518366] mtk_soc_eth 10100000.ethernet eth0: entered promiscuous mode
205. [   64.699390] br-lan: port 1(eth0.1) entered blocking state
206. [   64.704949] br-lan: port 1(eth0.1) entered forwarding state
207. [   81.175721] br-lan: port 2(phy1-ap0) entered blocking state
208. [   81.181617] br-lan: port 2(phy1-ap0) entered disabled state
209. [   81.187367] rt2800_wmac 10180000.wmac phy1-ap0: entered allmulticast mode
210. [   81.194748] rt2800_wmac 10180000.wmac phy1-ap0: entered promiscuous mode
211. [   82.982645] br-lan: port 3(phy0-ap0) entered blocking state
212. [   82.988526] br-lan: port 3(phy0-ap0) entered disabled state
213. [   82.994369] mt76x2e 0000:01:00.0 phy0-ap0: entered allmulticast mode
214. [   83.001283] mt76x2e 0000:01:00.0 phy0-ap0: entered promiscuous mode
215. [   86.415429] br-lan: port 2(phy1-ap0) entered blocking state
216. [   86.421235] br-lan: port 2(phy1-ap0) entered forwarding state
217. [   90.860874] br-lan: port 3(phy0-ap0) entered blocking state
218. [   90.866613] br-lan: port 3(phy0-ap0) entered forwarding state
219. [  173.112205] urngd: v1.0.2 started.
220. [ 1219.428927] mt76x2e 0000:01:00.0: Firmware Version: 0.0.00
221. [ 1219.434638] mt76x2e 0000:01:00.0: Build: 1
222. [ 1219.438820] mt76x2e 0000:01:00.0: Build Time: 201607111443____
223. [ 1219.468193] mt76x2e 0000:01:00.0: Firmware running!
224. [ 1219.474804] ieee80211 phy0: Hardware restart was requested
225.