root@OpenWrt:~# dmesg [ 0.000000] Linux version 6.6.73 (builder@buildhost) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r28427-6df0e3d02a) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 Mon Feb 3 23:09:37 2025 [ 0.000000] Board has DDR2 [ 0.000000] Analog PMU set to hw control [ 0.000000] Digital PMU set to hw control [ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc) [ 0.000000] MIPS: machine is TP-Link Archer C5 v4 [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.000000] Writing ErrCtl register=0003e4f3 [ 0.000000] Readback ErrCtl register=0003e4f3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16240 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 55152K/65536K available (6658K kernel code, 620K rwdata, 880K rodata, 1240K init, 241K bss, 10384K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] CPU Clock: 580MHz [ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns [ 0.000000] systick: enable autosleep mode [ 0.000000] systick: running - mult: 214748, shift: 32 [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns [ 0.000002] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns [ 0.007676] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216) [ 0.073580] pid_max: default: 32768 minimum: 301 [ 0.090795] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.097853] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.116767] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=1. [ 0.133811] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.143396] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.153267] pinctrl core: initialized pinctrl subsystem [ 0.162395] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.168955] thermal_sys: Registered thermal governor 'step_wise' [ 0.173087] /pinctrl: Fixed dependency cycle(s) with /pinctrl/pinctrl0 [ 0.460362] PCI host bridge to bus 0000:00 [ 0.464302] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff] [ 0.471014] pci_bus 0000:00: root bus resource [io 0x10160000-0x1016ffff] [ 0.477647] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.485408] pci 0000:00:00.0: [1814:0801] type 01 class 0x060400 [ 0.491198] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 0.497286] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff] [ 0.503497] pci 0000:00:00.0: supports D1 [ 0.507339] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 0.514933] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.522976] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000 [ 0.528796] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit] [ 0.535436] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 0.541987] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 0.548252] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 0.554643] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01 [ 0.561122] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 0.567487] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 0.574265] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff] [ 0.580844] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref] [ 0.587869] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff] [ 0.594461] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit] [ 0.601577] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref] [ 0.608569] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.613397] pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff] [ 0.619978] pci 0000:00:00.0: bridge window [mem 0x20100000-0x201fffff pref] [ 0.628696] clocksource: Switched to clocksource systick [ 0.647550] NET: Registered PF_INET protocol family [ 0.652604] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.661452] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.669704] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.677185] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.684638] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.691497] TCP: Hash tables configured (established 1024 bind 1024) [ 0.698511] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.705922] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.712268] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.720200] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.725754] PCI: CLS 0 bytes, default 32 [ 0.729824] rt-timer 10000100.timer: maximum frequency is 1220Hz [ 0.742913] workingset: timestamp_bits=14 max_order=14 bucket_order=0 [ 0.751365] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.756983] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.773836] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.783419] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.796119] printk: console [ttyS0] disabled [ 0.800897] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103 [ 0.810613] printk: console [ttyS0] enabled [ 0.819068] printk: bootconsole [early0] disabled [ 0.867288] spi spi0.0: force spi mode3 [ 0.872096] spi-nor spi0.0: s25fl064k (8192 Kbytes) [ 0.877211] 6 fixed-partitions partitions found on MTD device spi0.0 [ 0.884190] Creating 6 MTD partitions on "spi0.0": [ 0.889157] 0x000000000000-0x000000020000 : "u-boot" [ 0.898291] 0x000000020000-0x0000007c0000 : "firmware" [ 0.906659] 2 tplink-fw partitions found on MTD device firmware [ 0.912805] Creating 2 MTD partitions on "firmware": [ 0.917878] 0x000000000000-0x000000277421 : "kernel" [ 0.922957] mtd: partition "kernel" doesn't end on an erase/write block -- force read-only [ 0.933880] 0x000000277424-0x0000007a0000 : "rootfs" [ 0.939051] mtd: partition "rootfs" doesn't start on an erase/write block boundary -- force read-only [ 0.950970] mtd: setting mtd3 (rootfs) as root device [ 0.956250] 1 squashfs-split partitions found on MTD device rootfs [ 0.962635] 0x000000650000-0x0000007a0000 : "rootfs_data" [ 0.970854] 0x0000007c0000-0x0000007d0000 : "config" [ 0.978513] 0x0000007d0000-0x0000007e0000 : "rom" [ 0.986544] 0x0000007e0000-0x0000007f0000 : "romfile" [ 0.994745] 0x0000007f0000-0x000000800000 : "radio" [ 1.038057] gsw: setting port4 to ephy mode [ 1.049178] mtk_soc_eth 10100000.ethernet: port 5 - using fixed link parameters [ 1.056900] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver [ 1.063805] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5 [ 1.073244] rt2880_wdt 10000120.watchdog: Initialized [ 1.081109] NET: Registered PF_INET6 protocol family [ 1.094576] Segment Routing with IPv6 [ 1.098443] In-situ OAM (IOAM) with IPv6 [ 1.102747] NET: Registered PF_PACKET protocol family [ 1.107966] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.121584] 8021q: 802.1Q VLAN Support v1.8 [ 1.171335] clk: Disabling unused clocks [ 1.186836] VFS: Mounted root (squashfs filesystem) readonly on device 31:3. [ 1.200933] Freeing unused kernel image (initmem) memory: 1240K [ 1.206988] This architecture does not have kernel memory protection. [ 1.213597] Run /sbin/init as init process [ 1.217773] with arguments: [ 1.217780] /sbin/init [ 1.217786] with environment: [ 1.217793] HOME=/ [ 1.217799] TERM=linux [ 2.188969] init: Console is alive [ 2.193140] init: - watchdog - [ 3.731312] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.829307] usbcore: registered new interface driver usbfs [ 3.835099] usbcore: registered new interface driver hub [ 3.840689] usbcore: registered new device driver usb [ 3.850674] gpio_button_hotplug: loading out-of-tree module taints kernel. [ 3.882445] phy phy-usbphy.0: remote usb device wakeup disabled [ 3.888528] phy phy-usbphy.0: UTMI 16bit 30MHz [ 3.893078] ehci-platform 101c0000.ehci: EHCI Host Controller [ 3.898974] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1 [ 3.907227] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000 [ 3.923295] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00 [ 3.931080] hub 1-0:1.0: USB hub found [ 3.936149] hub 1-0:1.0: 1 port detected [ 3.951545] rtl8367b rtl8367s: using MDIO bus 'mdio' [ 3.957392] rtl8367b rtl8367s: RTL8367S-VB chip found (num:6642 ver:0010) [ 4.309894] rtl8367b rtl8367s: alloc vlan mc emulator [ 4.324947] rtl8367b rtl8367s: cpu_port:7, assigned to extif1 [ 4.759212] ohci-platform 101c1000.ohci: Generic Platform OHCI controller [ 4.766285] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2 [ 4.774522] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000 [ 4.810367] hub 2-0:1.0: USB hub found [ 4.815413] hub 2-0:1.0: 1 port detected [ 4.833116] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 4.845299] init: - preinit - [ 8.848933] random: crng init done [ 10.539003] mtk_soc_eth 10100000.ethernet eth0: port 5 link up (1000Mbps/Full duplex) [ 10.547976] 8021q: adding VLAN 0 to HW filter on device eth0 [ 12.336769] jffs2: notice: (487) jffs2_build_xattr_subsystem: complete building xattr subsystem, 138 of xdatum (14 unchecked, 124 orphan) and 142 of xref (124 dead, 0 orphan) found. [ 12.355794] mount_root: switching to jffs2 overlay [ 12.363796] overlayfs: upper fs does not support tmpfile. [ 12.394397] urandom-seed: Seeding with /etc/urandom.seed [ 12.508087] mtk_soc_eth 10100000.ethernet eth0: port 5 link down [ 12.542460] procd: - early - [ 12.545756] procd: - watchdog - [ 13.161681] procd: - watchdog - [ 13.166581] procd: - ubus - [ 13.325946] procd: - init - [ 15.384485] kmodloader: loading kernel modules from /etc/modules.d/* [ 16.169961] jitterentropy: Initialization failed with host not compliant with requirements: 9 [ 16.655528] Loading modules backported from Linux version v6.12.6-0-ge9d65b48ce1a [ 16.663268] Backport generated by backports.git v6.1.110-1-35-g410656ef04d2 [ 17.334344] mt76x2e 0000:01:00.0: card - bus=0x1, slot = 0x0 irq=4 [ 17.341046] mt76x2e 0000:01:00.0: ASIC revision: 76120044 [ 18.060480] mt76x2e 0000:01:00.0: ROM patch build: 20141115060606a [ 18.091170] mt76x2e 0000:01:00.0: Firmware Version: 0.0.00 [ 18.096810] mt76x2e 0000:01:00.0: Build: 1 [ 18.101055] mt76x2e 0000:01:00.0: Build Time: 201607111443____ [ 18.166259] mt76x2e 0000:01:00.0: Firmware running! [ 18.189490] mt76x2e 0000:01:00.0: registering led 'mt76-phy0' [ 18.197494] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 18.473090] PPP generic driver version 2.4.2 [ 18.500675] NET: Registered PF_PPPOX protocol family [ 18.652189] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected [ 18.660731] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 7620 detected [ 18.669777] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht' [ 19.137843] jitterentropy: Initialization failed with host not compliant with requirements: 9 [ 20.019722] kmodloader: 1 module could not be probed [ 20.025122] kmodloader: - jitterentropy_rng - 0 [ 64.373745] mtk_soc_eth 10100000.ethernet eth0: port 5 link up (1000Mbps/Full duplex) [ 64.382699] 8021q: adding VLAN 0 to HW filter on device eth0 [ 64.490953] br-lan: port 1(eth0.1) entered blocking state [ 64.496528] br-lan: port 1(eth0.1) entered disabled state [ 64.502177] eth0.1: entered allmulticast mode [ 64.506640] mtk_soc_eth 10100000.ethernet eth0: entered allmulticast mode [ 64.513977] eth0.1: entered promiscuous mode [ 64.518366] mtk_soc_eth 10100000.ethernet eth0: entered promiscuous mode [ 64.699390] br-lan: port 1(eth0.1) entered blocking state [ 64.704949] br-lan: port 1(eth0.1) entered forwarding state [ 81.175721] br-lan: port 2(phy1-ap0) entered blocking state [ 81.181617] br-lan: port 2(phy1-ap0) entered disabled state [ 81.187367] rt2800_wmac 10180000.wmac phy1-ap0: entered allmulticast mode [ 81.194748] rt2800_wmac 10180000.wmac phy1-ap0: entered promiscuous mode [ 82.982645] br-lan: port 3(phy0-ap0) entered blocking state [ 82.988526] br-lan: port 3(phy0-ap0) entered disabled state [ 82.994369] mt76x2e 0000:01:00.0 phy0-ap0: entered allmulticast mode [ 83.001283] mt76x2e 0000:01:00.0 phy0-ap0: entered promiscuous mode [ 86.415429] br-lan: port 2(phy1-ap0) entered blocking state [ 86.421235] br-lan: port 2(phy1-ap0) entered forwarding state [ 90.860874] br-lan: port 3(phy0-ap0) entered blocking state [ 90.866613] br-lan: port 3(phy0-ap0) entered forwarding state [ 173.112205] urngd: v1.0.2 started. [ 1219.428927] mt76x2e 0000:01:00.0: Firmware Version: 0.0.00 [ 1219.434638] mt76x2e 0000:01:00.0: Build: 1 [ 1219.438820] mt76x2e 0000:01:00.0: Build Time: 201607111443____ [ 1219.468193] mt76x2e 0000:01:00.0: Firmware running! [ 1219.474804] ieee80211 phy0: Hardware restart was requested